Protect position vs initialization #38
Replies: 4 comments 3 replies
-
|
Park position is 270° Azimuth, 45° elevation used for maintenance... |
Beta Was this translation helpful? Give feedback.
-
|
Sorry I mean protect position. When sequence initialization is on going it will be not interupt by ananometer. So it will not stop initialization and switch to protect sequence according to my observation. Its correct? |
Beta Was this translation helpful? Give feedback.
-
|
correct, it has to first initialize since the actuators do not provide
position feedback. it will not accept any other commands until the
initialization is completed
…On Mon, Jul 11, 2022 at 10:48 AM Robertarduino ***@***.***> wrote:
Sorry I mean protect position. When sequence initialization is on going it
will be not interupt by ananometer. So it will not stop initialization and
switch to protect sequence according to my observation. Its correct?
—
Reply to this email directly, view it on GitHub
<#38 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABIYATPOVE7ZZ5VHB2WR6FTVTQX2LANCNFSM53G2JLHQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
Graham A. Ross
(613) 769-1331
|
Beta Was this translation helpful? Give feedback.
-
|
From safety point of view. If signal from anometer is active, better to go at 90dgr and continue to reach East position. After reach continue to 180dgr. It's very dangerous to wait in initialization if strong wind appears. |
Beta Was this translation helpful? Give feedback.
-
|
it only initializes once after a reboot
…On Mon, Jul 11, 2022 at 11:31 AM Robertarduino ***@***.***> wrote:
From safety point of view. If signal from anometer is active, better to go
at 90dgr and continue to reach East position. After reach continue to
180dgr. It's very dangerous to wait in initialization if strong wind
appears.
What do you think?
—
Reply to this email directly, view it on GitHub
<#38 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABIYATJN4DZMIDFJHMLDMUTVTQ43ZANCNFSM53G2JLHQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
Graham A. Ross
(613) 769-1331
|
Beta Was this translation helpful? Give feedback.
-
|
In case of power failure or short ON/OFF during storm it will cause panel in 0dgr. |
Beta Was this translation helpful? Give feedback.
-
|
my tracker is powered from my 24V batteries with a buck converter to 12V
I'll be offline (going sailing) for a couple of weeks
…On Mon, Jul 11, 2022 at 11:37 AM Robertarduino ***@***.***> wrote:
In case of power failure or short ON/OFF during storm it will cause panel
in 0dgr.
—
Reply to this email directly, view it on GitHub
<#38 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABIYATP3BIC3TY4TI4R7IPTVTQ5SLANCNFSM53G2JLHQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
--
Graham A. Ross
(613) 769-1331
|
Beta Was this translation helpful? Give feedback.
-
What is the priotity for movment? ( situation whit hight wind speed) Initialization or Protect? After observation first is Initialization + plus waiting time after Protect position activation after strong wind.
In real situation its very dangerous because when big wind speed panels request is to go to 0dgr position and after to protect position.
Beta Was this translation helpful? Give feedback.
All reactions