Routing-Contents.md

Routing Contents

Router Components	❱ CPU ❱ IOS ❱ ROM ❱ RAM ❱ Flash Memory ❱ NVRAM ❱ Configuration Register ❱ IOS Booting Sequence ❱ Interfaces Console Port Aux port Serial Port Ethernet/Fast Ethernet/Gigabit Ethernet Port WIC Port HWIC Port ❱ Interface Numbering Fixed Ports Slot/Port Numbering Slot/Subslot/Port Numbering ❱ Copy Command ❱ Show Version Command
Router Modes	❱ How to Connect to Cisco Device ❱ GUI and CLI ❱ Setup Mode ❱ User Execution Mode ❱ Privileged Mode ❱ Global Configuration Mode ❱ ROMMON Mode ❱ IOS Navigation
Router Passwords	❱ Line Command ❱ Configuring Passwords Console Password Enable Password Secret Password Aux Password ❱ service password-encryption ❱ Removing Passwords Console Password Enable Password Secret Password Aux Password ❱ Routers Password Types ❱ Privilege Level Security ❱ Configuring Different Privilege Levels to Passwords ❱ Login vs Login Local Command
Telnet	❱ hostname Command ❱ show ip interface Command ❱ interface Command ❱ ip address Command ❱ shutdown Command ❱ ping Command ❱ VTY ❱ Line VTY Command ❱ Telnet ❱ Removing Telnet Password
SSH	❱ Encryption Symmetric Encryption Asymmetric Encryption Hybrid Encryption ❱ SSH ❱ SSH Encryption ❱ SSHv1 vs SSHv2 ❱ Setting up SSH ❱ Examining Telnet & SSH in Wireshark
Password Recovery	❱ Configuration Register Settings ❱ Password Recovery
Router Banners	❱ MOTD banner ❱ Login banner ❱ Exec banner
Syslog Messages	❱ Cisco IOS Syslog Messages ❱ Syslog Message Format ❱ Local History ❱ Syslog Server ❱ logging synchronous Command ❱ Clock Commands
LLDP & CDP	❱ CDP ❱ CDP Commands ❱ LLDP ❱ LLDP Commands
DTE & DCE	❱ Serial Cable Connection ❱ DTE ❱ DCE ❱ CSU/DSU ❱ Show Controllers Command ❱ Clock Rate Command ❱ Example
Static Routing	❱ Routers ❱ Functions of a Router ❱ Routing Table ❱ How are Routing Tables populated? ❱ Static Routing ❱ Dynamic Routing ❱ Static Routing vs Dynamic Routing ❱ Default Gateway ❱ Static Route Configuration (Lab 1) ❱ Exit Interface vs Next-hop ❱ Loopback Interfaces ❱ Default Route ❱ Routing Loop ❱ Maximum Hop Count ❱ Floating Static Route (Lab 2)
Some Definitions	❱ Routed Protocol ❱ Routing Protocols ❱ Autonomous System ❱ Routing Protocols Categories IGP EGP ❱ Administrative distance (AD) ❱ Routing Metric Value Hop count Delay (or Latency) Bandwidth Load Cost MTU
RIP	❱ RIP ❱ RIP Metric Value ❱ Equal cost load balancing ❱ How does the RIP work? ❱ RIP Packets ❱ RIP Timers Update timer Route invalid timer Route flush timer Hold-down timer ❱ A Distance Vector Routing ❱ Count to Infinity Problem in Routing ❱ Solution for the Count to Infinity Problem TTL Route Poisoning Split Horizon Hold-down Timer ❱ RIP Route Poisoning ❱ RIP Version 1 ❱ RIP Version 2 ❱ RIPv1 vs RIPv2 ❱ RIP Authentication Key Chain ❱ RIP Basic Configurations (Lab 1) ❱ RIP Authentication (Lab 2) ❱ RIP Equal Cost Load Balance (Lab 3) ❱ Floating Static Route (Lab 4)
Summarization	❱ Summarization (Supernetting) ❱ Route Summarization Steps ❱ Example 1 ❱ Example 2
OSPF	❱ Distance Vector vs Link State Protocols ❱ Link ❱ State ❱ Link State Protocol ❱ Hierarchical Design and Areas ❱ Some Terms ❱ Transit Area ❱ OSPF Metric Cost ❱ SPT (Shortest Path Tree) ❱ OSPF Neighborship Requirements ❱ OSPF Neighborship States ❱ Down State ❱ Hello Packet ❱ RID Manual configuration Loopback interface IP configuration Active interfaces IP configuration ❱ Attempt/Init State ❱ Two Ways State ❱ Types of Networks Point to point Network Broadcast Networks NBMA Netowrks Point to Multipoint ❱ DR and BDR ❱ DR and BDR Election Process ❱ Adjacency ❱ Exstart State ❱ Relative Terms LSA LSDB DBDs ❱ Exchange State ❱ Loading State ❱ Full State ❱ Maintaining Adjacency ❱ OSPF Process ID ❱ Wildcard masks ❱ Broadcast Network (Lab 1) ❱ Point-to-Point Network (Lab 2) ❱ Lab 3 ❱ Lab 4

---